Over time, your precious sex doll will acquire several, damages no matter how much you take care of it. Some damages will require you to buy new parts for it. On the other hand, there are also some types of damages that are reparable using some tools at home.

But if you are a person who owns as TPE sex doll, yet do not have enough knowledge about repairing it, then you are most likely to find a repair guide on the internet. And while you may think that fixing a damaged sex doll requires so much time and effort, this repair guide will prove you wrong.

Moreover, one thing you should note when you are fixing a sex doll is that the amount of time you spend on repairing it depends on the severity of the damage. If the damage is minor, such as abrasions, tears, and pressure marks, then it would not take too long for you to fix it.

To help you repair your beloved TPE sex doll, below are some of the easy methods that you can follow:

Method #1. Fixing Pressure Marks Using A Hairdryer

Over time, your sex doll may acquire indentations due to pressure applied to its body. This pressure marks can also come from improper handling or improper positioning of the doll during sex. However, you do not have to sweat because this damage is reparable using only a hairdryer.

To start the process, get a clean towel and wet it. Use a white towel if possible as coloured cloths may stain your doll’s skin. Cover the indentations with the wet towel and then heat it with the hairdryer.

Repeat this process a number of times. As you do it, you will notice that the indentation on your TPE sex doll will disappear little by little.

Method #2. Using A Hot Towel to Fix Dents

Wear a glove in order to protect your hand from the heat of the towel. Get a clean towel and wet it with hot water. Next, cover the pressure dent with the hot towel for some time. Once the damaged part of your sex doll has already acquired the heat from the towel, use your hand to pat it gently. Do this process repeatedly until the indentation is fixed. Method #3. Fixing Abrasions On the Sex Doll’s Skin Using the Heat Gun Procedure Before blowing the heat gun on the surface of the doll, clean it first using either Vaseline or baby oil. Applying baby oil or Vaseline serves two important purposes. First, it sterilizes the surface where the damage is. Second, it helps you apply the heat on the surface of the doll more evenly. This will help you prevent the sex doll’s skin from burning.

After applying either of the two substances, proceed with heating the damaged surface using a heat gun. Make sure that the heat gun is not too close to the skin of your sex doll. Placing it too close to the surface may burn your doll’s skin, thus causing even more damage. About four inches of distance between the doll and the device is enough to prevent any further damage caused by heat.

If it is your first time to repair a doll using a heat gun, the best thing you can do is to buy a test TPE material and practice the process on it. You can acquire a TPE material from a TPE vendor. Practice the heat gun method on it until you get familiar with how to properly do the process.

The melting point of a TPE doll’s skin is at around 110 degrees Celsius. Once you reached that point, you will notice that the part where you are blowing heat will have a glaze-like mirror finish. Observe the intensity of the fume as it will tell you when you should stop blowing heat.

Once you reached the right point, get a piece of cloth and use it to feather out the abrasions on the doll’s skin. Repeat the heating and cooling process until you reach the right smoothness of the sex doll’s skin.

Method #4. Use A TPE Glue to Seal Tears

Before applying glue on your sex doll’s torn up skin, it would be best if you will clean it with cleaning agents such as soap, makeup remover, or nail polish remover. Then, make sure that the damaged skin is completely dry.

Moreover, make sure that the doll is properly positioned. The torn area must be placed horizontally in order to avoid the glue from overflowing. Once the doll is in the correct position, apply the TPE glue using a fine-tipped applicator. This process requires a minute precision in order to get the best results.

In addition, prepare a clean cloth before applying the glue on the doll. Once you have already applied the TPE glue, stick the torn parts together and squeeze out the excess glue. Wipe it out with a clean cloth to make sure that the repaired area is as smooth as possible.

Another thing worth noting when using TPE glue to repair your sex doll is to avoid using your fingers in wiping the excess glue. TPE glue sets fast so touching it with your fingers will cause unwanted marks, thus ruining the smoothness of your sex doll’s skin. Furthermore, you can fix your sex doll’s facial cuts using a similar method. However, it requires more practice. If you fail to do the process perfectly, you will not be able to get your desired smoothness for the face of your doll.

But if your doll has damage on its face, the best thing that you can do is to buy a new head for your doll. Although it would cause you quite an expensive price, it will still be worth it since your doll will look as good as new. The most genuine brand of doll heads costs more or less $400. This is already an excellent bargain considering the benefits and unique looks that your doll will get.
By Irontech .


Just added to your wishlist:
My Wishlist
You've just added this product to the cart:
Go to cart page